View TB62205F_37218.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
TB62205F
TOSHIBA BiCD Process Integrated Circuit Silicon Monolithic
TB62205F
Single-Stepping Motor Driver IC with Dual DC/DC Converter Driven by Chopper Micro-Step Pseudo Sine Wave
The TB62205F is a single-stepping motor driver with dual DCDC converter driven by chopper micro-step pseudo sine wave. To drive a two-phase bipolar-type stepping motor, a 16-bit latch and a 16-bit shift register are built in the IC. The TB62205F is suitable for driving stepping motors at high efficiency and with low-torque ripple, and supports Selectable Mixed Decay Mode for switching the attenuation ratio at chopping. Also, the IC incorporates two DCDC converters, enabling two individually configurable power supplies.
Features
* One stepping motor driven by micro-step pseudo sine wave is
controlled by a single driver IC
Weight: 0.79 g (typ.)
* Enables to drive two-way supply voltage using a pair of step-down DC/DC converters * Monolithic Bi-CMOS IC
Low ON-resistance of Ron = 0.7 (@Tj = 25C, 1.0 A: typ.)
* Motor block incorporating 16-bit serial-in shift register, 16-bit latch and 4-bit D/A converter for micro step
drives
* * * * * * * * * *
On-chip 5-V regulator for internal circuit, enabling single power supply operation (VM) for the motor .com On-chip ISD and TSD circuits, and internal VDD/VM power-on reset circuit as protection circuits On-chip charge pump circuit (two external capacitors) Package: 36-pin power flat package (P-HSOP 3620-450-0.65) Motor maximum power supply voltage: 30 V (max), motor output current: 0.7 A (max) DCDC converter maximum input current: 1.2 A (max), maximum load current: 0.96 (A) On-chip Mixed Decay Mode enables specification of four-stage attenuation ratio. Chopping frequency can be set by external oscillator. High-speed chopping is possible at 100 kHz or higher. Also, DCDC frequency can be set by the external OSC. To set chopping at 100 kHz or higher is possible
DataShee
Note: When using the IC, pay attention to thermal conditions. These devices are easily damaged by high static voltage. In regards to this, please handle with care. A schottky barrier diode (SBD) should be inserted between the output pin of the DCDC converter and ground. (Recommended device: Toshiba CMS07)
.com
1
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Block Diagram
1. Overview
Torque Torque S0 S1 RS D33 FB1
DCout33
RS D12
FB12 DCout12
D_OSC
D_OSC
INV_IN
DC/DC converter 1 (3.3 V) Decay table setting circuit
DC/DC converter 2 (12 V)
DCDC12 STOP
Motor RESET SETUP
DATA CLK STROBE Current setting circuit Torque control circuit 4-bit D/A (angle control) Waveform shaping circuit Current controll data logic circuit 16-bit shift register Chopping reference circuit Chopping waveform generating circuit
16-bit latch
M_OSC
Vref
Current feedback circuit VRS circuit 1 RS COMP circuit 1 Output control circuit
RS
t4U.com
VM VRS circuit 2
.com
RS COMP circuit 2
DataShee
Ccp 2 Charge pump circuit
Output circuit (H-bridge)
ISD circuit
TSD circuit
Ccp 1
VM-VDD regulator
VDDR/VMR circuit Protected circuit
Out X
VM_MO
Stepping motor High-voltage wiring (VM) Logic DATA Analog DATA IC pin
.com
2
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
2. Logic unit for motor driver
Function
This circuit is used to input from the DATA pins micro-step current setting data and to transfer them to the subsequent stage. By switching the SETUP pin, the data in the mixed decay timing table can be rewrite External input data and the 2-bit input signal from 16-bit shift register can be used to set the torque circuit. When 1 is input to one of them, 1 is reflected such as a function of OR gate.
Micro-step current setting data logic circuit 16-bit shift register B unit side
SETUP
CLK 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DATA
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 16-bit latch A unit side
STROBE
TORQUE 1
INV_IN (CLK/STROBE)
TORQUE 2
t4U.com
Motor RESET Torque x 2 bit
.com
DataShee
Phase x 1 bit B unit side
Decay x 2 bit B unit side
Current x 4 bit B unit side
Current feedback circuit
DA circuit
Output control circuit
Mixed decay timing table selector
Mixed decay timing
Output control circuit
Note: The Motor RESET and SETUP pins are pulled down in the IC by 100 k resistor. When the SETUP pin and the TORQUE pin are not used, connect them to ground. Otherwise, malfunction may occur.
.com
3
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
3. Current feedback circuit and current setting circuit for motor driver
Function
The current setting circuit is used to set the reference voltage of the output current using the micro-step current setting data input from the DATA pins. The current feedback circuit is used to output to the output control circuit the relation between the set current value and output current. This is done by comparing the reference voltage output to the current setting circuit with the potential difference generated when current flows through the current sense resistor connected between RS and VM. The chopping waveform generator, to which a capacitor is connected, generates clock (OSC-CLK) used as reference for the chopping frequency, so that these two circuits are pure digital logic.
Torque 0.1
Logic unit
Torque 0.3
Vref
100% 75% 50% 25%
Torque control circuit
t4U.com
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Chopping waveform generator circuit Microstep current setting selector circuit
M_OSC
Waveform shaping circuit 4-bit .com D/A Chopping reference circuit circuit
Mixed decay timing circuit
DataShee
Current setting circuit
Output stop signal (ALL OFF)
RS VM
VRS circuit 1 (detects potential difference between RS and VM) VRS circuit 2 (detects potential difference between VM and RS)
Use in charge mode RS COMP circuit 1 (Note 1) Output control circuit
NF (set current reached signal)
RS COMP circuit 2 (Note 2)
RNF (set current monitor signal) Use in fast mode
Current feedback circuit
Note 1: RS COMP1: Compares the set current with the output current and outputs a signal when the output current reaches the set current. Note 2: RS COMP2: Compares the set current with the output current at the end of Fast mode during chopping. Outputs a signal when the set current is below the output current.
.com
4
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
4. Output control circuit, current feedback circuit and current setting circuit for motor driver
Micro-step current setting data logic circuit Chopping reference circuit
Output control circuit
Phase
Decay mode
Mixed Decay Timming circuit
Current feedback circuit
NF set current reached signal RNF set current monitor signal MIXED DECAY TIMMING Charge Start U1 U2 L1 Output control circuit L2
OSC counter
OSC counter
Current setting circuit
Output stop signal
Output circuit
Output RESET signal Motor RESET ISD (current shutdown) circuit Charge pump
VDD
VM Power supply for upper output MOS transistors VH
Output circuit Ccp A
t4U.com
Output pin
.com halt signal
Reset signal selector circuit Charge pump circuit
DataShee
VM
VMR circuit
Ccp B
Internal VM + VDD (VH)
VHR circuit
Ccp C Charge pump circuit
Thermal shut down (TSD) circuit Protection circuit MICRO-STEP CURRENT SETUP LATCH CLEAR signal Logic VDDR : VDD power on monitor VMR : VM power on monitor ISD : Current shutdown circuit TSD : Thermal shutdown circuit VM-VDD regulator MIXED DECAY TIMMING TABLE CLEAR signal
VM internal VDD
Note: The Motor RESET , and SETUP pins are pulled down in the IC by a 100-k resistor. When these pins are not used, connect them to ground. If they are left open, malfunction may occur.
.com
5
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
5. Output equivalent circuit for motor driver
RS A Output driver circuit U1 U2 L1 L2
To VM RRS A
U1
U2
From output control circuit
OUT A Power supply for upper output MOS transistors (VH) OUT A L1 L2
Phase A VM B
Output driver circuit U1 U2 L1 L2
RS B
RRS B
U1
U2
t4U.com
.com
OUT B M
From output control circuit
DataShee
OUT B
Power supply for upper output MOS transistors (VH)
L1
L2
Phase B PGND
.com
6
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
6. DCDC conversion circuit
RRS_D1 To VM DCDC12_STOP RS_D1
COSC_D
D_OSC
Control circuit (12 V) Charge pump for motor driver ISD DCout12
To output L1
RA 1 C1
ISD DC_SBD1 FB12
RA 2
Control circuit (3.3 V or 5 V)
RS_D12 RRS_D 2
Recommended SBD: CMS07 To VM
ISD
t4U.com
ISD
.com
DCout 3.3
L2 To output
RB 1 C2
DataShee
FB 3.3
DC_SBD2
RB 2
DCDC READY
C_DCDC READY (recommended value: 10000 pF or more)
.com
C1
7
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Pin Descriptions
Pin No. 1 2 3 4 5 6 7 Pin Symbol VM TORQUE S0 TORQUE S1 INV_IN VSS1 NC OUT A Pin Description Power supply monitor pin for output part External motor torque setting pin for motor External motor torque setting pin for motor Inverse input pin for motor CLK and STROBE Ground pin for LOGIC part (Please connect the pin 5 to FIN.) Not connected
Motor A output pin Motor A channel current detection pin (power supply pin) Motor A output pin FIN (VSS): Ground pin for LOGIC Motor B output pin Motor B channel current detection pin (power supply pin) Motor B output pin Not connected Ground pin for LOGIC part (Please connect the pin 14 to FIN.) Motor STROBE (latch) signal input pin (: LATCH Motor lock input pin (: CLK @ INV_IN: L) @ INV_IN: L)
8 9 FIN 10 11 12 13 14 15 16 17 18
RS A OUT A FIN OUT B RS B OUT B NC VSS2 STROBE CLK DATA OSC_M VDD_MO Vref SETUP
Motor RESET
Motor serial data signal input pin External chopping reference pin for motor, that sets the chopping frequency.
t4U.com
19 20 21 22 23 24 25 26 27 FIN 28 29 30 31 32 33 34 35 36
.com Internal power supply monitor pin for logic part (Internal power supply)
Motor Vref input pin Mode switching pin for Motor SETUP (L: Motor operation, H: Motor switching) Motor stopping pin (L: RESET) Output stopping pin for DCDC 12 V Voltage feedback pin for DCDC 12 V PGND for DCDC 12 V Power supply input pin (sense resistor connecting pin) for DCDC 12 V Power voltage output pin for DCDC 12 V FIN (VSS): Ground pin for LOGIC part Power voltage output pin for DCDC 3.3 V Power supply input pin (sense resistor connecting pin) for DCDC 3.3 V PGND for DCDC 3.3 V Power voltage feedback pin for DCDC 3.3 V Pin for setting start delay time of DCDC 3.3V Capacitor connection pin for DCDC oscillating frequency Capacitor pin for charge pump (Ccp 2) Capacitor pin for charge pump (Ccp 2) Capacitor pin for charge pump (Ccp 1)
DataShee
DCDC12STOP DCDC12FB P-GND12 RS_DC12 DCDC12OUT FIN DCDC3.3OUT RS_D3.3 PGND3.3 DCDC3.3FB DCDC READY OSC_D Ccp C Ccp B Ccp A
Note: When the IC is mounted in the wrong orientation, high voltage will be applied to the low-withstand-voltage block, which causes the IC to be destroyed. Please check the pin 1 positioning mark when mounting it. While the IC is powered-on, do not connect the motor to the IC or vice-versa.
.com
8
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Function 16-bit serial input signals for motor
(apply the signals in reverse order of TB62201AF serial input signals.)
Data Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Phase A Current A3 Current A2 A-channel current setting Current A1 Current A0 Decay Mode A1 A-channel current attenuation ratio setting Decay Mode A0 Phase B Current B3 Current B2 B-channel current setting Current B1 Current B0 Decay Mode B1 B-channel current attenuation ratio setting Decay Mode B0 Torque 1 Torque setting Torque 0 Phase information (H: out B is high) Name Function Phase information (H: out A is high)
Strobe
t4U.com
CLK DATA
.com
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
DataShee
Note: The direction of DATA and CLK indicated above is under the condition of when INV_IN = H.
.com
9
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Data input signal at setting mixed decay timing table
(Apply the signals in reverse order of TB62201AF data input signals.)
Data Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Name Current Mode 3 Decay Mode 3-2 Decay Mode 3-1 Decay Mode 3-0 Current Mode 2 Decay Mode 2-2 Decay Mode 2-1 Decay Mode 2-0 Current Mode 2 Decay Mode 1-2 Decay Mode 1-1 Decay Mode 1-0 Current Mode 0 Decay Mode 0-2 Decay Mode 0-1 Decay Mode 0-0 Sets decay 0 ratio Selects Slow or Mixed Decay Mode Sets decay 1 ratio Selects Slow or Mixed Decay Mode Sets decay 2 ratio Selects Slow or Mixed Decay Mode Sets decay 3 ratio (decay 3 ratio) Function Selects Slow or Mixed Decay Mode Initial Value 1: Mixed Decay Mode 1 1 1: 100% 1: Mixed Decay Mode 1 0 1: 75% 1: Mixed Decay Mode 0 1 0: 37.5% 0: Mixed Decay Mode 0 0 0: 12.5%
Strobe CLK
t4U.com
DATA
0 1 2 .com 10 11 12 13 14 15 3456789
DataShee
Note: The direction of DATA and CLK indicated above is under the condition of when INV_IN = H.
Table for Setting (1)
Setting Phase A
Data Bit 0
D0
Name Phase A
Function Switching phases
Phase 0 1
Setting Value Phase OUT A = L, OUT A = H OUT A = H, OUT A = L
.com
10
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Table for Setting (2)
Setting Current
Data Bit 1 2 3 4 Step 16 15 14 13 12 8 9 10 11 11 10 9 8 7 6 5 4 3 2 1 0 A3 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 A2 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 A1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 A0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 B3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 B2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 B1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 B0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 Setting Angle (degree) 90 84 79 73 68 61 56 51 45 39 34 28 23 17 11 6 0
D1, D2, D3, D4, D8, D9, D10, D11
Table for Setting (3)
t4U.com
D5, D6, D12, D13
.com
Name Function Setting Decay Mode Decay Mode 1 Decay Mode 0 0 0 1 1 0 1 0 1 Setting Value Decay Mode Mixed Decay Mode: 12.5% Mixed Decay Mode: 37.5% Mixed Decay Mode: 75.0% Fast Decay Mode
Setting Decay Mode
Data Bit 5 6
DataShee
Decay Mode A1 Decay Mode A0
Table for Setting (3)
Setting Phase B
Data Bit 7
D7
Name Phase B
Function Switching phases (+side, -side)
Phase 0 1
Setting Value Phase OUT B = L, OUT B = H OUT B = H, OUT B = L
Table for Setting (3)
Setting Torque
Data Bit 0 1
D14, D15
Name Torque 0 Torque 1
Function Setting current range
Torque 1 0 0 1 1
Torque 0 0 1 0 1
Setting Value Torque (typ.) 25% 50% 75% 100%
.com
11
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Function of External Input Pins
External Torque 1.2
Pin Number 3 2 Name TORQUE S1 TORQUE S0 Function Setting current range Torque 1 0 0 1 1 Torque 0 0 1 0 1 Setting Value Torque (typ.) 25% 50% 75% 100%
When 1 is applied to either the external Torque 1.2 or the serial data Torque 1.2, 1 is reflected such as a function of OR gate.
INV_IN
Pin number 4 Name INV_IN Function Determine which direction to reflect the STROBE CLK of the serial data input. Torque 1 H Setting Value Torque (typ.) The same direction as TB62201AF Down CLK Up Edge Strobe The opposite direction from TB62201AF Up CLK Down Edge Strobe
L
t4U.com
.com
DataShee
.com
12
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Maximum Ratings (Ta = 25C)
Characteristics Motor/DCDC power supply voltage Motor output current Maximum DCDC converter input current Maximum DCDC initial charge current Maximum constant output current Maximum Vref voltage range Current detect pin voltage Maximum voltage at charge pump (CCP1) pin Logic input voltage Power dissipation Operating temperature Storage temperature Junction temperature Symbol VM IOUT IDCOUT IDCOUT_S IDCconst Verf VRS VH VIN PD Topr Tstg Tj Rating 30 0.7 1.2 0.8 IDCOUT x 0.8 4.0 VM 4.5 VM + 7.0 Up to 5.7 1.4 W 3.2
-40 to 85 -55 to 150
Unit V A/phase A A A V V V V
Remarks
(Note 1) (Note 2) (Note 3) (Note 4)
Inside regulator (Note 5) (Note 6) (Note 7)
C C C
150
t4U.com
Note 1: Perform thermal calculations for the maximum current value of the motor under normal conditions. Use the IC at 0.6 A or less per phase. Note 2: Under the condition of DCDC output voltage x 0.9 V or higher (typ.) In this case, the input current to the power supply becomes the current value (1.2 A) that is controlled by the sense resistor. Note 3: Under the condition of DCDC output voltage x 0.9 V or lower (typ.)
.com
Note 4: The output current is lower by 20% than the input current value of the DCDC converter (calculated value). When The value of IDCOUT is 1.2 A (max), the output current will be 0.96 A (max). Note 5: Input 5.5 V or less as VIN. Note 6: Measured for the IC only. (Ta = 25C) Note 7: Measured when mounted on the board. (Ta = 25C) Ta: IC ambient temperature Topr: IC ambient temperature when starting operation Tj: IC chip temperature during operation Tj (max) is controlled by TSD (thermal shutdown circuit) Note : Notes on maximum voltage This device does not incorporate an overvoltage protection circuit. When an excessive voltage is applied to the device, it may be destroyed. Thus, make sure that the power supply voltage is within the specification value.
DataShee
.com
13
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Recommended Operating Conditions (Ta = 0C to 85C)
Characteristics Voltage range Motor output current DCDC converter current range DCDC initial charge current Maximum constant output current Logic input voltage Clock frequency Motor chopping frequency DCDC chopping frequency Vref reference voltage Current detect pin voltage Symbol VM IOUT IDCOUT IDCOUT_S Test Condition
Min 14

Typ. 24 0.4 1.0 0.6 0.8
Max 28 0.6 1.1 0.7 0.84 5 25 150 150 3.0
1.5
Unit V A A A A V MHz kHz kHz V V
Ta = 25C, per phase

Maximum DCDC initial charge IDCOut_Const current x 0.8 VIN fCLK fchop_M fchop_D Vref VRS VM = 24 V VM = 24 V VM = 24 V VM = 24 V

GND
1.0 100 100 2.0
1.0
40 40 0 0
Note: In terms of the temperature withstand capability, the maximum value of Tj should be approximately 120C.
Operating Precaution
This device does not incorporate an overvoltage protection circuit. Thus, if an excess voltage is applied to the IC, the IC may be destroyed. Please design the IC so that an excess voltage will not be applied to the IC.
t4U.com
.com
DataShee
.com
14
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Motor Electrical Characteristics 1
Characteristics High Input voltage Low Input hysteresis Input current 1 VIN (L) VIN (HIS) IIN1 (H) IIN1 (L) IIN2 (H) IIN2 (L) DC Motor RESET , SETUP pins OUT = open, motor logic = L DCDC3.3 ON (100-kHz external operation) VM = 24 V, motor output stage = OFF Charge pump = charged Ccp1 = 0.22 F, Ccp2 = 0.02 F OUT = open, fchop = 100 kHz (phase input 200 kHz) DCDC3.3 ON (100-kHz external operation) VM = 24 V, motor output stage = open Charge pump = charged Ccp1 = 0.22 F, Ccp2 = 0.02 F OUT = open, chopping = 100 kHz DCDC3.3 ON (100-kHz external operation) DCDC12 ON (100-kHz external operation) Charge pump = charged Ccp1 = 0.22 F, Ccp2 = 0.02 F
RS M out = 0 V,
(unless otherwise specified, Ta = 25C, VM = 24 V, Ccp1 = 0.22 F, Ccp2 = 0.022 F)
Symbol VIN (H) DC DC Test Circuit Test Condition CLK, Motor RESET , STROBE, DATA Torque 0, Torque 1, SETUP pins CLK input pin CLK, STROBE, DATA pins Min 2.0 GND - 0.4

Typ. 3.3 GND 0.3
Max 5.4
Unit
V 0.8
V
A A
1.0 1.0 100 100

Input current 2
IM1
8
12
15
Current dissipation (Pin VM)
IM2
DC
22
24
26
mA
IM3
24
30
35
t4U.com
Output standby current Output bias current Output leakage current
Upper
IOH IOB IOL VRS (H) VRS (MH)
.com V = V = 24 V, V
Motor RESET = H, DATA = all L
-400 -200
-300 -120
-200 -80
A A A
DataShee
Upper
DC
VRS = VM = 24 V, Vout = 24 V, RESET = H, DATA = all L VRS = VM = Ccp A = Vout = 24 V,
Motor RESET = L
Lower HIGH (reference)
1.0
Vref = 3.0 V, Vref (gain) = 1/4.0 TORQUE = (H.H) = 100% setting Vref = 3.0 V, Vref (gain) = 1/4.0 TORQUE = (H.L) = 75% setting Vref = 3.0 V, Vref (gain) = 1/4.0 TORQUE = (L.H) = 50% setting Vref = 3.0 V, Vref (gain) = 1/4.0 TORQUE = (L.L) = 25% setting DC DC DC Differences between output current channels Iout = 700 mA Iout = 700 mA VRS = 24 V, VM = 24 V, Motor RESET = L (RESET status) Iout = 1.0 A, Tj = 25C, Drain-source DC Iout = 1.0 A, Tj = 25C, Source-drain Iout = 1.0 A, Tj = 105C, Drain-source Iout = 1.0 A, Tj = 105C, Source-drain
100 75 50 25

Comparator reference voltage ratio
MID HIGH MID LOW LOW
73 48 23
-5 -5
77 % 52 27 5 5 10 0.85 0.85 1.1 1.1
DC VRS (ML) VRS (L)
Iout1 Iout2
Output current differential Output current setting differential RS pin current
% %
A
IRS RON (D-S) 1
0.7 0.7 0.9 0.9
Output transistor drain-source On-resistance
RON (S-D) 1 RON (D-S) 2 RON (S-D) 2
.com
15
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Motor Electrical Characteristics 2
Characteristics Internal logic power supply voltage Vref input voltage Vref input current Vref attenuation ratio
(unless otherwise specified, Ta = 25C, VM = 24 V, Ccp1 = 0.22 F, Ccp2 = 0.022 F)
Symbol VDD Vref Iref Vref (gain) TjTSD TSD temperature Note 1) VM return voltage Over current protected circuit operation current ISD ( Note 2) DC VMR DC Motor RESET = H, STRBE = H fchop = 100 kHz set 10.5
Test Circuit DC DC DC DC
Test Condition Automatically created Motor RESET = H, Output on
Motor RESET = H, Output off, Vref = 3.0 V
Min 4.7 0 20 1/3.8
Typ. 5.0
Max 5.3 3.3 60 1/4.2
Unit V V
A
45 1/4
Motor RESET = H, Output on, Vref = 0 V to 3.3 V
(
DC
130
150 11.0 3.0
170 11.5
C V A
Note 1: Thermal shutdown (TSD) circuit When the IC junction temperature reaches the specified value and the TSD circuit is activated, the internal reset circuit is activated switching the outputs of both motors to off. When the temperature is set between 130 (min) to 170C (max), the TSD circuit operates. When the TSD circuit is activated, the function data latched at that time are cleared. Output is halted until the reset is released. While the TSD circuit is in operation, the charge pump is halted. Note 2: Overcurrent protection circuit When current exceeding the specified value flows to the DCDC output, the internal reset circuit is activated switching the outputs of both shafts to off. When the ISD circuit is activated, the function data latched at that time are cleared. .com The overcurrent protection circuit remains activated until the VM voltage is reapplied. Activating the ISD initializes all the circuits in the IC, which causes the charge pump to be stopped. For the failsafe operation, insert a fuse in the power supply.
t4U.com
DataShee
.com
16
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Motor Electrical Characteristics 3
Characteristics
(Ta = 25C, VM = 24 V, Iout = 0.7 A, Ccp1 = 0.22 F, Ccp2 = 0.022 F)
Symbol Test Circuit Test Condition
A = 90 (16) A = 84 (15) A = 79 (14) A = 73 (13) A = 68 (12) A = 62 (11) A = 56 (10) A = 51 (9)
Min

Typ. 100 100 98 96 92 88 83 77 71 63 56 47 38 29 20 10 0
Max

Unit
93 91 87 83 78 72
97 93 88 82 76 68 61 52 43 34 25 15
Chopper current
Vector
DC
A = 45 (8) A = 40 (7) A = 34 (6) A = 28 (5) A = 23 (4) A = 17 (3) A = 11 (2) A = 6 (1) A = 0 (0)
66 58 51 42 33 24 15 5
%
t4U.com
DCDC Converter Electrical Characteristics 1 (unless otherwise specified, Ta = 25C, .com VDD = 3.3 V, VM = 24 V, Ccp1 = 0.22 F, Ccp2 = 0.022 F)
Characteristics Symbol Test Circuit Test Condition Output voltage error Vout = 3.3 V, FB with 1% resistor 0.96 A, C = 470 F, L = 470 F DCDC output voltage error (DCDC load regulation)
Vout2
DataShee
Min
Typ.
Max
Unit
Vout1
DC
Output voltage error Vout = 3.3 V, FB with 1% resistor Iout = 0.7 A, C = 470 F, L = 470 F, VM = 12-28 V
-5
0
5
%
DCDC Pin FB input current Pin FB threshold voltage Soft/full switching voltage ratio DCDC output off leak current DCDC Maximum duty cycle
IIN (FB) Vth (FB) VDC_SF IODC DC_duty RON (D-S) 1 RON (D-S) 1
DC DC DC DC DC
VM = 24 V, VIN (FB)

500
nA V % nA %
2.5 92

Iout = 700 mA VM = 24 V, upper VM = 24 V, lower
90
-200 -400
94

90 0.7 0.7 0.9 0.9
Iout = 1.0 A, Tj = 25C, forward direction Iout = 1.0 A, Tj = 25C, opposite direction DC Iout = 1.0 A, Tj = 105C, forward direction Iout = 1.0 A, Tj = 105C, opposite direction
0.84 0.84
Output transistor drain - source ON resistance
RON (D-S) 2 RON (D-S) 2
1.1 1.1
.com
17
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
AC Characteristics for Motor Driver
Characteristics Motor clock frequency Symbol fCLK tw (CLK) Motor minimum clock pulse width twp (CLK) twn (CLK) tSTROBE Motor minimum STROBE pulse width tSTROBE (H) tSTROBE (L) Motor data setup time tsuSIN-CLK tsuST-CLK Motor data hold time thSIN-CLK thCLK-ST tr tf Motor output transistor switching characteristic tpLH (ST) tpHL (ST) tpLH (CR) tpHL (CR) Motor noise rejection dead band time tBLNK fCR fchop (min) Motor chopping frequency range fchop (typ.) fchop (max) Motor motor chopping frequency fchop (M) AC AC AC AC AC AC AC
(Ta = 25C, VM = 24 V, 6.8 mH/5.7 , Ccp1 = 0.22 F, Ccp2 = 0.022 F)
Test Circuit AC Test Condition
Min 1.0 40
Typ.

Max 25

Unit MHz
AC
20 20 40
ns
AC
20 20 20 20 20 20

ns
ns
ns
Output load: 6.8 mH/5.7 STROBE () to VOUT Output load: 6.8 mH/5.7 CR to VOUT Output load: 6.8 mH/5.7 Iout = 0.7 A Cosc = 560 pF Output active (Iout = 0.7 A) Step fixed, Ccp 1 = 0.22 F, Ccp 2 = 0.022 F Output active (Iout = 0.7 A) M_osc CLK = 800 kHz Ccp2 = 0.22 F, Ccp = 0.02 F VM = 24 V, VMR = OFF are reference voltages
0.1 0.1 15 10 1.2 2.5 300 840
s
180 640
400 1000
ns kHz
t4U.com
Motor CR reference signal oscillation frequency
.com
DataShee
40
100
150
kHz

105
kHz
Charge pump rising time
tONG
AC
0.5
1.0
ms
AC Characteristics for DCDC Converter
(Ta = 25C, VM = 24 V, 470 H, 470 F)
Characteristics Output transistor switching characteristic DCDC reference signal oscillation frequency DCDC setting frequency range Symbol tr_D tf_D fOSC_D fchop_D AC AC Cosc = 560 pF
Test Circuit AC
Test Condition 470 H/470 F
Min

Typ. 0.1 0.1 90 100
Max

Unit
s
kHz kHz
40
150
.com
18
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Test Circuit (DC characteristics)
MOSC = 560 pF
Iref
M_OSC Vref
A
3V
Vref
5V 0V 5V 0V
A
STROBE CLK VM RRS A DATA A
A
IM1, IM2, IM3 A V VRS Iout 1, 2
Stepping motor RRS A
SGND
A A A A A A
5V 0V 5V 0V
0V 5V 0V 5V 0V
1.0
A IOL IOH IOB
SETUP Motor RESET
B M
B
TORQUE S0 TORQUE S1 P-GND VSS (FIN) SGND RRS B
A IRS
RRS B
1.0
PGND
5V 0V 5V 0V
SBD (CMS07) IDcout_const
470 F
A A
DCDC12_STOP INV_IN DCDC12OUT
L2 470 H
1 F
V VDCout
DCDC12FB
C_DCDC READY = 10000 pF
t4U.com
V
DCDC_READY .com
DataShee
IDcout_const
470 F
M_OSC = 500 pF
D_OSC
DCDC3.3OUT 470 H DCDC3.3FB IDcout_S, IDCout RRS DC3.3 = 0.51
100 F
V VDCout
V
1.0 F
RS_D3.3
Ccp A
Ccp B
RS_D12 RRS DC12 = 0.51 Ccp C
SGND
Ccp1 0.22 F
V
Ccp2 0.022 F
SGND
.com
19
.com DataSheet 4 U .com
2005-04-04
24 V
VDD_MO
www..com
TB62205F
Test Circuit (AC characteristics)
FCLK, tw (CLK), twp (CLK), twn (CLK) TSTROBE, tSTROBE (H), tSTROBE (L) TsuSin-CLK, tsuST-CLK, thSin-CLK, thCLK-ST
MOSC = 560 pF
Iref M_OSC Vref A
3V
fchop (M), fsoc_M 5V 0V 5V 0V 5V 0V 5V 0V 0V 5V 0V 5V 0V
Vref A STROBE CLK A A A A A A DATA SETUP MOTOR RESETVM RRS A A
A
IM1, IM2, IM3 A RRS A 1.00
SGND tBLNK
B M
B
TORQUE S0 TORQUE S1 P-GND PGND VSS (FIN) SGND RRS B A IRS
Stepping motor RRS B 1.00
SBD (CMS07) IDcout_const
5V 0V
A A
DCDC12_STOP INV_IN DCDC12OUT DCDC12FB
t4U.com
5V 0V
.com 470 H
470 F
1 F
tr, tf, tpLH, (ST) tpLH (ST) tpHL (ST) tpLH (CR) tpHL (CR)
DataShee
tr_D, tr_D
V
C_DCDC READY = 10000 pF
DCDC_READY DCDC3.3OUT DCDC3.3FB
D_OSC
D_OSC = 560 pF
470 H
470 F
fchop (D), fosc_D
tr_D, tr_D
1.0 F
V
Ccp A
Ccp B
RRS DC12 RS_D12 Ccp C RRS DC33 = 0.40
SGND
Ccp1 0.22 F
t ONG
Ccp2 0.022 F
SGND
.com
100 F
RS_D3.3
20
.com DataSheet 4 U .com
2005-04-04
24 V
VDD_MO
www..com
TB62205F
Calculation of Set Current
To obtain the motor setting current value (peak current), values of RRS, Vref and Torque should be determined according to the equation below.
I out (max) = 1 Torque (torque = 100, 75, 50, 25% : input serial data) x Vref (V) x Vref (gain ) R RS ( )
1/Vref (gain): 1/Vref attenuation ratio is 1/4.0 (typ.). For example, to input Vref = 1 V and Torque = 100% and to output Iout = 0.25 A, RRS = 1.0 (0.1 W or more) is required.
Formulas for Calculating Reference Oscillation Frequency (chopping reference
frequency)
The M_osc oscillation frequency (fosc_M) and, chopping frequency (fchop) can be calculated by the following formulas : fosc_M = 1 [Hz] x (CR x 36000R + x C)
KA (constant): 0.523 KB (constant): 600 R = 3.6 k (internal resistor)
fchop = M_osc [Hz] 8
t4U.com
Example: When COSC = 560 pF is connected, M_osc = 813 kHz. At this time, the chopping frequency fchop is: fchop = fosc/8 = 101 kHz. .com Note: fchopc =
1 fosc
DataShee
tosc_M = t (charge) + t (discharge) tosc_M: Motor OSC oscillation cycle t (charge): Motor OSC charge time
DCDC Converter Oscillating Frequency
fDCDC (DCDC PWM frequency) = 50 ()/(0.8 x COSC_D) (Hz) PWM frequency for DCDC block is about 100 kHz when COSC_D is 620 pF. Example: COSC_D = 680 pF: 91 kHz = 620 pF: 100 kHz = 560 pF: 111 kHz = 510 pF: 122 kHz = 470 pF: 133 kHz = 390 pF: 160 kHz
.com
21
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Startup Sequence of Power Supply (Voltage)
(1) When VM supply voltage exceeds VMR voltage, charge pump reset is cleared. (2) When charge pump voltage exceeds the normal voltage (Cp R) and after the DCDC_READY time delayed, 3.3-V (5 V) DC/DC converter reset is cleared, and 3.3-V DCDC goes up. (3) The DC/DC converter operated with soft switching Mode at initial charging up through 90 % of the normal voltage by current controlling. After that, the converter is operated with full-charging Mode. (4) When external signal becomes High, 12-V DCDC starts charging. (12-V DCDC is switched from the soft switching Mode to the full Mode same as the 3.3-V DCDC.)
VM VMR Motor supply voltage (External input)
t_DCDC_Start
0V Charge pump reset (Internal signal) tONG (Charge pump rise time) VM + 5 V Cp R Charge pump voltage VM DCDC reset (Internal signal) 3.3 V DCDC3.3 V (Output) DCDC_R (3.3 V x 90
)
t4U.com
DCDC3.3 V Mode
.com
Full switching Mode Soft switching Mode H
DataShee
DCDC12_STOP (External input)
L 12 V
DCDC12 V Full switching Mode DCDC12 V Mode Soft switching Mode
Motor RESET Possible input range
H L H L
Normal voltage Achieved signal
.com
22
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Graph of the Power Supply on DCDC Input Side
5 V (3.3 V) 90%
The current capacity is automatically increased when the level of specified voltage x 90% is
The power supply is activated when the current is constant. (Example: 0.8 A) 0.4 A 0.8 A 1.2 A
Equations for Calculating Maximum Current Values in Soft-Start Mode and Full Mode
The values of limited current of the DCDC block in Soft-start Mode and Full Mode are obtained using the following equations. (1) When the specified voltage is 0% to 90% of the voltage range The maximum current value in Soft-start Mode : I DCout_S = 0.33/R RS_D33 (or D12) (A) (2) When the specified voltage is 90% to 100% of the voltage range The maximum current value in Full Mode : I DC_out = I DCout_S x 1.5 (A) When the current is specified in Full Mode, the current value which can be driven out is obtained .com using the following equation. The maximum load current : I DCout_const = I DC_out x 0.8 (A)
t4U.com
DataShee
.com
23
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Relationship between VM and VH (charge pump voltage)
VM - VH (& V charge up)
50
VH voltage
Charge-up voltage
VM voltage
40 Charge pump output voltage
Apply the STNDBY signal.
(V) VH voltage, Charge-up voltage
30
VM voltage VMR
20 Maximum rating
t4U.com
.com
DataShee
10
Recommended usage
Usable range
0 0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Power supply voltage VM (V) Charge pump voltage VH = VDD + VM (= Ccp A)
(V)
Note:
VDD = 5 V
Ccp1 = 0.22 F, Ccp2 = 0.022 F, fchop = 150 kHz (Keep in mind that the temperatures of the charge pump capacitors change.)
.com
24
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Charge Pump Circuit Operation
RRS VDD = 5 V RS VM
VM = 24 V
VH
Ccp A
7
i2 Di2 Output Comparator and Controller Tr2 Vz Output H switch Tr1 Di3 R1 Di1 (1) (2) i1 (2) Ccp B
Ccp2 0.022 F
Ccp C
VH = VM + VDD = Charge pump voltage i1 = Charge pump output current i2 = Gate consumption current At initial charging When the RESET circuit is released, Tr1 is turned on. Then Tr2 is turned off and Ccp2 is charged from the VM power supply via Di1. (2) When Tr1 is turned off and Tr2.com charged from Ccp2 via Di2. is turned on, Ccp1 is (3) When the potential difference between VM and VH (Ccp A pin voltage = charge pump voltage) reaches VDD or higher, the operation of the charge pump circuit stops. (In Full Mode) When IC is operating (4) (5) Ccp1 charge is used at fchop switching and the VH potential drops. Charges up by (1) and (2) above. (1)
t4U.com
Ccp1 0.22 F
DataShee
Output switching Initial charging Full Mode
VH VM
(1)
(2)
(3) t
(4)
(5)
(4)
(5)
.com
25
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
External Constant of Charge Pump
When VDD = 5V, fchop = 100 kHz, and L = 10 mH is driven with VM = 24 V, Iout = 1000 mA, the theoretical values for Ccp1 and Ccp2 are as shown below:
Ccp1 - Ccp2
0.05 Usable range 0.045 0.04 Ccp1 = (NG) Ccp2 = (OK) Recommended range
Ccp2 capacitance (F)
0.035 0.03 0.025 0.02 0.015 0.01 0.005 0 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Recommended value
Ccp1 capacitance (F)
For the combination of Ccp1 and Ccp2, please refer to the shaded area in the figure above. Toshiba recommends the relation of Ccp1 : Ccp2 10 : 1. When the values of Ccp1 and Ccp2 are specified, perform an adequate test and allow sufficient margins for the values. Please use the recommended values of Ccp1 = 0.22 F and Ccp2 = 0. 022 F for normal operation.
t4U.com
.com
DataShee
.com
26
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Startup Time of Charge Pump
VDD + VM VM + (VDD x 90%)
Ccp1 voltage
VM
5V
STANDBY
0V
50%
tONG
t4U.com
tONG: Time taken for capacitor Ccp2 (charging capacitor) to fill up Ccp1 (capacitor used to save charge) to VM + VDD after a reset is released. Until the voltage of Ccp1 reaches VM + VDD, the motor and the DCDC converter do not operate normally. To prevent erroneous operations, the TB62205F incorporates a protection circuit. When the voltage of the charge pump is increased up to the specified level, the motor can operate standalone. However, the initial charging of the DCDC converter starts at this timing. Thus, the DCDC .com converter startup time should be included when the system startup time is set. Basically, the larger the Ccp1 capacitance, the longer the initial charge-up time but the smaller the voltage fluctuation. The smaller the Ccp1 capacitance, the shorter the initial charge-up time but the larger the voltage fluctuation. Depending on the combination of capacitors (especially with small capacitance), voltage may not be sufficiently boosted. Thus, use the capacitors under the capacitor combination conditions (Ccp1 = 0.22 F, Ccp2 = 0.022 F) recommended by Toshiba.
DataShee
.com
27
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Operating Time of Overcurrent Protection Circuit
ISD non-detection time and ISD operating time
Output stops (RESET mode) CR oscillating (chopping reference waveform) min max
(Non-detection time) ISD BLANK time
min max ISD operating time
When overcurrent starts to flow into the output stage (overcurrent state occurs)
The overcurrent protection circuit has a non-detection time to prevent erroneous detection of spike current generated in diode recovery current (IRR) or at switching. The non-detection time being synchronized with the CR cycle for setting chopping frequency is expressed as follows. Non-detection time = 4 x CR cycle
t4U.com
Time required to stop the output after overcurrent flows into the output stage is expressed as follows. Minimum time = 5 x CR cycle Maximum time = 8 x CR cycle Note that the operating times as shown above are achieved when overcurrent flows as it is expected. Depends on the timing of output control mode, the circuit may not be triggered. Thus, to ensure safe operation, please insert a fuse in the VM power supply. (The capacity of the fuse is determined according to a condition to be used. Please select one whose capacity does not exceed the power dissipation for the IC to avoid any operating problems.)
.com
DataShee
.com
28
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Example of Application Operation Input Data (4-bit micro-step drive)
Torque 0 Bit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 15 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Torque 1 14 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Decay B0 13 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Decay B1 12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0 11 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 B1 10 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 B2 9 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 B3 8 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 Phase B 7 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Decay A0 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Decay A1 5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 A0 4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 A1 3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 A2 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 A3 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 Phase A 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
t4U.com
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
.com
DataShee
.com
29
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Torque 0 Bit 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 15 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Torque 1 14 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Decay B0 13 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Decay B1 12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
B0 11 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1
B1 10 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1
B2 9 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1
B3 8 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1
Phase B 7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Decay A0 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Decay A1 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
A0 4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0
A1 3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0
A2 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0
A3 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Phase A 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
t4U.com
53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68
.com
DataShee
Data are applied on the rising edge of CLK. Every input of a data string (16-bit) requires input of the Strobe signal. For the function of the input signals, please refer to the section "Function". In the above input data example, Decay Mode has a Mixed Decay mode (37.5%) setting for both the rising and falling directions of the sine wave, and a torque setting of 100%.
.com
30
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
4W 1-2 Phase Excitation Output Current Waveform (4-bit micro-step drive)
[%] 100 98 96 92 88 83 77 71 63 56 47 38 Phase A 29 20 Phase B 10
0
-10 -20 -29 -38 -47 -56 -63 -71 -77 -83 -88 -92 -96 -98 -100
.com
Step
17-step micro-step drive from 0 to 90 can be achieved by combining Current DATA (AB and CD) and phase data. For the input current data, please refer to "Current A0 to A3 and B0 to B3" in the section "Function".
t4U.com
Depending on the load, the optimum condition changes for selecting Mixed Decay Mode when the sine wave rises and falls. Select the appropriate Mixed Decay timing according to the load.
DataShee
.com
31
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Output Current Vector Locus
4W 1-2 Phase Excitation (4-bit micro-step drive)
X = 16 X = 15 X = 14 X = 13 X = 12 X = 11 X = 10 83 X=9 77
100 98 96 92 88
71
X=8 X=7
63
X=6 56
IA (%)
47
X=5
38
X=4
29
X=3
t4U.com
20
.com
X
X=2
DataShee
10 X
X=1
X=0 0 10 20 29 38 47 56 63 71 77 83 88 92 96 98 100
IB
(%)
For the input data, please refer to the "Function" column in the "Current" row in the section "Function".
.com
32
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Output Vector Locus 2 (Modes other than 4 W 1-2 phase)
1-2 phase excitation (typ. A)
100 100
1-2 phase excitation (typ. B)
71
IA (%)
IA (%)
0
100
0
71
100
IB
(%)
IB
(%)
W 1-2 phase excitation
100 92 100 98 92 83 71 71 56
2W 1-2 phase excitation
t4U.com
IA (%)
.com
38 38
IA (%)
DataShee
20
0
38
71
92 100
0
20
38
56
71
83 92 98 100
IB
(%)
IB
(%)
.com
33
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
Application Circuit
MOSC = 560 pF
M_OSC
Vref
1 F
Vref STROBE CLK DATA SETUP MOTOR RESETB TORQUE 0 TORQUE 1 P-GND VSS (FIN) SGND RRS B VM RRS A A
A
5V 0V 5V 0V 5V 0V 5V 0V 5V 0V 5V 0V 5V 0V
RRS A 1.00
B M
Stepping motor
RRS B 1.00 @
PGND 5V 0V 5V 0V DCDC_STOP INV_IN
SBD (CMS07)
DCDC12OUT DCDC12FB
C_DCDC READY = 10000 pF
t4U.com
DCDC_READY .com DCDC3.3OUT DCDC3.3FB
470 F
470 F
470 H
3V
SGND
DataShee
470 H
M_OSC = 560 pF
D_OSC
1.0 F
RRS DC12 RS_D2 Ccp A Ccp B Ccp C RRS DC33 = 0.47
SGND
Ccp1 0.22 F
Ccp2 0.02 F SGND
.com
100 F
RS_D1
34
.com DataSheet 4 U .com
2005-04-04
24 V
VDD_MO
www..com
TB62205F
Package Dimensions
HSOP36-P-450-0.65 Unit: mm
t4U.com
.com
DataShee
Weight: 0.79 g (typ.)
.com
35
.com DataSheet 4 U .com
2005-04-04
www..com
TB62205F
RESTRICTIONS ON PRODUCT USE
t4U.com
* The information contained herein is subject to.com change without notice.
030619EBA
* The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The products described in this document are subject to the foreign exchange and foreign trade laws. * TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations.
.com
36
.com DataSheet 4 U .com
2005-04-04

▲Up To Search▲

Price & Availability of TB62205F

	To Download TB62205F Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .